Cadastre-se agora para um orçamento mais personalizado!

Automating Your Network Operations, Part 2 -Data Models

Sep, 26, 2018 Hi-network.com

Keeping|your|IT infrastructure operational

Before I get into data models, I want to take a slight diversion to incorporate some of the feedback that I received from the first blog. It was pointed out that my use of the ios_config module was "na?ve." I contend that it is more accurate to say that my use of Ansible in general was "na?ve," since this was a pretty straight forward use of the module. In any case, it was by design. Why? Well, if you are like the majority of the network operators that I've worked with over the years, you are not a programmer (or you are a "na?ve" programmer). You spend 110% of your time busting your chops making sure that the network that underpins your company's IT infrastructure is operational. I certainly do not want to discourage network operators going to classes, workshops, etc. to learn new skills if they have the time and the motivation, but it should not be necessary toconsumenetwork automation. We can do better!

The NTP example that I used in the first blog was also chosen for specific reasons. First, NTP and AAA were the questions that I got most from customers on this issue. They were able to configure these things initially, but ran into problems when they moved to an operational posture. Second, it is representative of the "na?ve" approach that you'll see in the examples and workshops that are being delivered in the Ansible network automation genre. These "naive" examples and workshops perpetuate the first reason. Lastly, there is no way to use the ios_config module, the most used Ansible module for Cisco IOS, to fix this. Nor is the issue addressed by an NTP-specific Ansible network module. Yes, there might be some other module in some git repo written by someone that addresses your corner case, but do you want to use it? Is writing a module for every single corner case for network automation a scalable approach? I say no. Partially because it is intractable, partially because it is a support nightmare.

Where do you get help for the modules that underpin the automation?

Red Hat supports a specific set of modules (generally the ones they write), other vendors support their modules, other modules are completely unsupported. Where do you get help for the modules that underpin the automation that makes your network work? Incidentally, we'll cover a technique to augment the ios_config module with a parser to address this problem in a later blog, but it is not intuitively obvious to the casual observer.

I believe that we need to focus on a smaller number of more capable modules and couple that with a more sophisticated, or more realistic, approach to network automation. Subsequent blogs will focus on different aspects of this more realistic approach, but this one will start with the biggest: Data Models.

So, what is a data model?

I know what you are thinking: "Wait a minute! I didn't need data models for automating my servers!" Well, building a system is a well-defined procedure with relatively few permutations or interdependencies on other systems. Also, provisioning a system generally consists of configuring values like hostname, IPs, DNS, AAA, and packages. Each of these are key/value pairs (e.g. nameservers = 8.8.8.8, 8.8.4.4) that define the operation of that system and there are relatively few of them for a system.

This is not the case for a network element. If we take a standard 48-port Top-of-Rack Switch, each port could have a description, a state, a VLAN, an MTU, etc. A single ToR could have hundreds of key/value pairs that dictate its operation. Multiply that across hundreds or even thousands of switches, and the number of key/value pairs grows rapidly. Collectively, all of these key/value pairs make up the Source of Truth (SoT) of your network and there can be a lot of them. In fact, automating networks is really more of a data management and manipulation problem than it is a programming problem.

So, what is a data model? Generally speaking, a data model is a structure in which the meaning of a key/value pair is defined by its relative position in that structure. As an example, let's start with the de-facto standard in the networking space: YANG. According to RFC 7950, "YANG is a data modeling language used to model configuration data, state data, Remote Procedure Calls, and notifications for network management protocols."

If we look at the way we setup a simple BGP peering on Cisco IOS and Juniper JunOS, we basically have a bunch of values accompanied by a bunch of words using a particular grammar that describe those values:

But the values, two ASNs and an IP address, are the only things that really matter and they are the same in each.

In fact, the switch hardware does not care about the words that describe those values since they get stored in a config DB anyway. The words are what the engineers gave to the humans to communicate the meaning of those values to the hardware. After all, we can't just specify 2 ASNs because we need to know which is the local and which is the remote. We could, however, communicate their meaning by order: e.g. <Local ASN>, <Peer ASN>, <Peer IP>. This is basically a small data model. Well, BGP gets A LOT more complicated, so we'll need a more capable data model. Here we have an example of the same data in the OpenConfig data model rendered in YAML:

The data in the model on the left contains the information needed to deliver either of the syntax specific versions... just add words. Yes, we still have words as tags in the model, but it normalizes those tags across vendors and gets rid of the grammar needed to specify how values relate to each other. We do not want to add words back if we can avoid it, so the next step is to encode all of this data into XML and shove it into the device via NETCONF.

NETCONF/YANG gives us programmability, but we still need automation since the two are not the same. This is where Ansible enters back into the story. In my opinion, it is the best of the open-source IaC tools for delivering data models to devices. I'll explain why and dig deeper into the power of data models in my next blog.

Want to learn more about data models before we start to use them in the next few blogs? Check out Model Driven Programmability at Cisco DevNet. As always, please drop me a comment on this blog if you have questions, or topics you'd like this series to cover.

Get your free DevNet account for access to network automation resources, learning labs, and sandboxes.


We'd love to hear what you think. Ask a question or leave a comment below.
And stay connected with Cisco DevNet on social!

Twitter @CiscoDevNet | Facebook | LinkedIn

Visit the new Developer Video Channel


tag-icon Tags quentes : network automation YANG Ansible data models network operations yaml

Copyright © 2014-2024 Hi-Network.com | HAILIAN TECHNOLOGY CO., LIMITED | All Rights Reserved.